I had put up my 10 meter dipole when I set up my ICOM 740, and had it at 16.5′. I had used a way out of the house for the feedline that had me using a lot of coax. I had trouble with SWR, I could tune it out but I was not very efficient. I found another way to get my coax out to my antenna and it knocked off about 45′ of the feedline, yes 45 feet. I was able to raise the top of the dipole to 21.5′ and now now roughly 12′ to bottom of mast of feedline. I still have a little off balance inverted V with the higher side pointing west, but only a few degrees different than east side.
Right off the bat I found 1:1.2 swr on my radio without tuner and this was at about 65% of RF power. Very little done on antenna tuner now to get it at 1:1 and if I go full power I can still tune it down perfectly. Next week I will be building my 50 ohm dummy load, just waiting on some resistors and need to go out and get my paint can and some mineral oil.
I found a good deal on both the General and Extra ARRL books so I have been reading those. I have been reading one section in the General book and then part2 so to speak in the Extra book. I am starting to pass the practice test for general, still marginal but I am passing about 60% of the time. Another week or two and I will raise that average.
I have quite a few projects on deck:
- Found some really nice surround speakers plus center speaker at Goodwill, Sony’s want to use them as externals for my HF rig.
- Have a LM386 Audio chip I am thinking of building into a mono amp to feed the Sony speakers, maybe build a small Eq tone stack to use as listening filters.
- Parts arriving for my homebuilt bench power supply will be here in a few days and time to get that project in a box.
- Have some 300ohm twin lead and some really old plans for a doublet dipole fed with coax and an air choke.
- Arduino parts arriving late in week and ready to start on my weather station project among others.
Until next time…
After gaining a few pieces of equipment at the hamfest I was eager to see about getting a more efficient setup on 2 meters. New amp and i had just finished reading “US Army RADIO WAVE PROPAGATION AND ANTENNAS” on my smartphone So I looked around the net for possible ideas and with what I had on hand I arrived at making a vertical dipole.
I started off with making a air choke in hopes of eliminating some of the static I get on 2meters.
I had a Monster, project box and a pill bottle, time to get busy.
I slotted the end of the box so I could slide in my l brackets I was going to use to bolt the copper tube to.
Used some stiff plastic as a stiffener and isolator
My pill bottle was about 1.5″ and I put on 6 winds of RG58U
All mounted in box, I mounted a pvc fitting to bottom so I could mount on my mast so the coax fed the center at a 90 degree angle. I will post pics of it mounted outside soon. The 7/8 copper pipe kinda test the pvc and my heavy fishing line guy lines.
It tuned in 1.3:1 on 5 watts and a bit higher when i turn the amp on. I can hit many more repeaters and certainly hear a lot more. I forgot to mention I raised the antenna to 16′ in the air where my old one was only at 10′. I still have this annoying pulsing static that I hear when listening to a few repeaters, I am still trying to pin down the cause of this.
I didn’t really like the yellowish backlight on my VHF/UHF SWR Meter so I opened it up and grabbed a blue LED to replace it with. I added a small toggle switch as well so I can power the backlight off without having to unplug the power from the back.
It had 12volts already coming in from a power supply so I had to find the right resistor to use on the LED. It is a basic formula:
To calculate the resistor needed for a simple LED circuit, simply take the voltage drop away from the source voltage then use Ohm’s Law.
- Es is the source voltage, measured in volts (V)
- Eled is the voltage drop across the LED, measured in volts (V)
- Iled is the current through the LED, measured in Amperes (Amps/A)
- R is the resistance, measured in Ohms (Ω)
so.. R=(Es – Eled) / iled
If you don’t want to bother with that you can go HERE
I needed a 560 Ohm resistor to make my LED work on 12volts
I just like the blue backlight!
Wish I had a little smaller switch to use but it gets the job done.
I am hoping to find a decent deal on an Antenna Tuner there and other goodies! Be nice to win that raffle as well but it will all be fun going to my first Hamfest.
A couple days before I took my test I had also received my first radio. To start off I wanted to get on the 2Meter band being as I could talk phone right away with a Technician’s license and I would be more likely to make contacts on local repeaters than trying on 10meter sideband right off. I was skeptical at spending too much right away as I didn’t know enough about what was to be had out there without a further education.
So after reading quite a bit on forums and reviews I decide to give the very affordable BaoFeng UV5R+ a shot.
It is a tidy little Handheld with most the features you need or would want. Programmable via cable or keypad, scans frequencies or memory channels and even has a flashlight and a decent Fm broadcast radio.
I found the best price on Amazon I picked up an programming cable, Mic and a TRAM model 1185 mobile dual band antenna for my Jeep. This is a lot of radio for 40 bucks is all I can say. 2Meters, 70CM bands. Can be used as police scanner, FMRS and MURS radio.
The stock software leaves a lot to be desired so I downloaded CHIRP and it works very well. I can load up repeaters from various sources and save the image of the radio etc. On my recent honeymoon through the Olympic Peninsula here in Washington State I was able to load up my radio with repeaters based on the counties I was going to be driving through.
I use this mostly at home with an outside antenna. Radioshack is among the many places you can get an adapter for this radio to connect to a PL-259. I built a couple different groundplane antennas that I have used to participate in a few local area Nets. I do have a little bit a trouble hitting all the repeaters which I thought was due to coax loss but a few tries in the car and just out in the yard with stock antenna I still feel a bit under powered. I run into a lot of I can hear them but they can not hear me. I am keeping my eyes out for a mobile with a little more power or a linear amp.
I had picked up a Daiwa CN-103L SWR/Power meter from a friend and both of the antennas I have made tuned up nicely, so I will connect to the repeaters I can until I get a few more vhf/uhf watts under my belt.
At 47 Years old I have a small story to tell, I will skip all the I was born stuff and just condense it to I grew up in Catholic family, in a small neighborhood looking at most of my world like it was an episode of The Andy griffin Show. I was always active in scouts from cub to boy scouts and that and my dad led me to the fascinating world of electronics.
In 4th grade I was old enough to graduate from Weblos to Boy Scouts and the troop I was involved in was where I met one of my life long friends who entered the world of electronics with me and still to this day works in the industry and the hobby. The Christmas after I joined the troop I received a Radio Shack 150 in 1 Experimenters kit. I had already worn in the reputation for liking to tear things apart and like most boys I could be entertained for hours with batteries, a flashlight and a dc motor. I fired up that Radio shack experimenters kit and built my first crystal radio. I had a bedroom in the basement that my dad had remodeled years before for my older brothers. He had built a nice desk and wrap around counter that hid the water meter, this was still back when the meter man had to read the meter in the house so it had a little trap door to lift to see the digits. For though it provided a great earth ground connection for my crystal radio. I spent countless evenings listening to skipped am radio stations from all over, constantly tuning as the station faded away. The seed was planted, within months most of the parts were torn of the experimenters board and made into various projects.
My friend in scouts too had started playing with circuits and was showing a greater aptitude than me already. My dad took me one day up to bunch of storage units where a guy was selling boxes of circuit boards and parts. I really wasn’t sure why we were there until my dad pointed to some boxes and told me load them into the car. On the way home he gave me the stern “I don’t want to see this all over my workshop”. He had built me my own workbench when I was 6 complete with tools and I was known for migrating his tools to my bench and leaving a mess about. My dad had just loaded me up with tons of parts to desolder from circuit boards and play with, I was in heaven.
The following summer as we uncovered our small above ground pool my friend and I started envisioning little electric boats. We had seen the guys down at the river with the RC hydroplanes, we had both had our share of COX control line planes and spent plenty of time building models and loitering in the local hobby shop. The whole hobby thing was in full motion. We started with Styrofoam and motors powered with propellers from broken rubber power balsa planes. We progressed to cutting water props out of pop cans and JB welding them onto motors. Running around the pool to turn your boat around was getting old and our medium had progressed to balsa wood carved and painted. I don’t remember which one of us it was but we took a cheap radio control car from Woolworths and tore it apart to control the rudder on one of the boats. Remember the early RC cars that only turned when they went in reverse? This was one of those. We both dreamed of ways we could achieve radio control on a 7th graders wages.
That fall at middle school or junior high as we called it then we both got to take an electronics elective class. Our collective proficiency got us into the job of running the class’s parts room where we got to be exposed to more parts than Radio shack had. We learned more, years went by we stayed near the hobbies of electronics. My friend designed circuit boards and still does research and design stuff as a contractor. I went on to 20 years in the bicycle business, some in the computer and IT trades and 10 years in the hobby RC industry.
Now years later I have 2 sons and a beautiful wife that supports all my hobbies and it is the perfect time to return to the things I enjoy and feed my mind a little bit. For years I have thought off and on about getting back into ham radio after playing with it in my early 20’s. I decided recently I knew most of the information for the Technicians test so I got an ARRL book, found practice tests online and went and took the test this last August. I passed and it began my journey of learning a lot of new things in this last month.
The bench has parts on it, the soldering iron is hot, I am tracking my first HF rig shipment to me, talking on 2meter repeaters with handheld and already starting to study for my General License test. Life is good.
I recently received the Call Sign KG7FDJ after passing my FCC Element 2 Technician test enabling me to operate an amateur radio on certain frequencies.
I used to be avid blogger about 10 years ago and have recently been looking for something to write about again. I like to write, I like most of you I have an opinion and like a lot of other older internet users I began my writing on the internet by being active with my opinion and words on forums and networks of blogs. Most of the words read or written had a certain heat to them fueled by politics and religion. Since those days I have lost most of my emotional energy to muster up a public opinion. My need to express my opinion was kept in check by my wisdom. My dad always told me never discuss politics or religion, little by little I listen to my father even though it takes me roughly 20 years per piece of advice.
Ham radio, electronics are some of the things that occupy my thoughts and I want to document my progress into the higher FCC amateur licenses, the things I am going to learn, the things I might pass on and the fun I am going to have.
So welcome to my words, hope to read yours and hope you enjoy reading mine.